Setra Systems SRPM Instructions d'exploitation télécharger pdf

Model SRPM

Room Pressure Monitor

Installation and Operating Manual

13.0 RETURNING PRODUCTS FOR REPAIR

Before returning the unit for repair, please contact a Setra application engineer (800-257-3872,

978-263-1400) to review information relative to your application . Many times only minor ﬁeld

adjustments may be necessary. When returning a product to Setra, the unit should be carefully

packaged and shipped prepaid to:

Setra Systems, Inc.

159 Swanson Road

Boxborough, MA 01719-1304

Attn: Repair Department

To assure prompt handling, please refer to return instructions on our Web site at

http://www.setra.com/tra/repairs/cal_rep.htm.

Allow approximately 3 weeks after receipt at Setra for the repair and return of the unit.

Non-warranty repairs will not be made without customer approval and a purchase order to

cover repair charges.

Calibration Services

Setra maintains a complete calibration facility that is traceable to the National Institute of

Standards & Technology (NIST). If you would like to recalibrate or recertify your Setra pressure

transducers or transmitters, please call our Repair Department at 800-257-3872 (978-263-1400)

for scheduling.

14.0 WARRANTY AND LIMITATIONS OF LIABILITY

Setra warrants its products to be free from defects in materials and workmanship, subject to the

following terms and conditions:

Without charge, Setra will repair or replace products to be found to be defective in materials or

workmanship within the warranty period; provided that:

a.) the product has not been subjected to abuse, neglect, accident, incorrect wiring not our own,

improper installation or servicing, or use in violation of instructions furnished by Setra;

b.) the product has not been repaired or altered by anyone except SETRA or its authorized service

agencies;

c) the serial number or product code has not been removed, defaced, or otherwise changed; and

d) examination discloses, in the judgement of SETRA, the defect in materials or workmanship

developed under normal installation, use and service;

e) SETRA is notiﬁed in advance of and the product is returned to SETRA transportation prepaid.

Unless otherwise speciﬁed in a manual or warranty card, or agreed to in a writing signed by a SETRA

ofﬁcer, SETRA pressure and acceleration products shall be warranted for one year from date of sale.

The foregoing warranty is in lieu of all warranties, express, implied or statutory, including but not

limited to, any implied warranty of merchantability for a particular purpose.

SETRA’s liability for breach of warranty is limited to repair or replacement, or if the goods cannot

be repaired or replaced, to a refund of the purchase price. SETRA’s liability for all other breaches is

limited to a refund of the purchase price. In no instance shall SETRA be liable for incidental or conse-

quential damages arising from a breach of warranty, or from the use or installation of its products.

No representative or person is authorized to give any warranty other than as set out above or to

assume for SETRA any other liability in connection with the sale of its products.

159 Swanson Road, Boxborough, MA 01719,

Tel: 800-257-3872; Fax: 978-264-0292;

Email: [email protected]; Web: www.setra.com

SS-SRPM Rev. A 5/1/2008

1 2 3 4 5 6 ... 13 14

Résumé du contenu

Page 1 - Room Pressure Monitor

1Model SRPMRoom Pressure MonitorInstallation and Operating Manual2813.0 RETURNING PRODUCTS FOR REPAIRBefore returning the unit for repair, please cont

Page 2 - Contents

103.3 Attaching Pressure TubingTypically a Room Pressure Snubber (RPS) is installed in the monitored room. Attach pressure tubing as follows:1. ) Conn

Page 3 - Contents (cont’d)

114.0 Model SRAN Room Annunciator Installation4.1 Alarm Relay OutputThe Single Pole Double Throw (SPDT) relay output can be used for remote signal-ing

Page 4

124.2 Audible AlarmAlarm potentiometer adjusts from 0 to 85 dBA. Using a screwdriver, rotate potentiometer clockwise to increase volume and counterclo

Page 5

131 V Out 0 to 5, 0 to 10 VDC 2 C Out 4 to 20 mA3 CommonFigure 11: Analog Output (J5)6.0 Electrical Installation6.1 Analog Output (J5)SRPM can be c

Page 6

14 15User’s Operating Instructions

Page 7 - Installation Instructions

2Contents1.0 Introduction ...51.1 Intended Use .

Page 8 - Press to Access Screen

3Contents (cont’d)7.5 SETUP ALARM SCREEN ... 21 7.5.1 Alarm Setup

Page 9

4Figure 1: Typical Installation259.0 MaintenanceThe SRPM is designed to operate in an indoor environment, monitor-ing clean, dry (see humidity speciﬁc

Page 10 - Password Setting Screen

51.0 IntroductionCongratulations, and thank you for purchasing Setra’s Room Pressure Monitor (Model SRPM). Its ease of operation and durable construct

Page 11

62.0 Parts List1.1 SRPM Parts List Qty (1) Setra SRPM assembly (2) Barbed Coupling, Brass (2) 1/4 inch Tube, Silicone, Inter-Connect (4) 6-32

Page 12

7Installation Instructions227.6.1 Self Test OperationThis screen identiﬁes the Product Model and Soft-ware Version. User can also perform a Self Test

Page 13 - Normal, Wa

8Figure 2: Location of Components and Accessories217.5 SETUP ALARM SCREEN 7.5.3 Data Entry ScreenEnter numbers by pressing each key in s

Page 14 - User’s Operating Instructions

93.0 Mounting and Wiring3.1 Mounting For 120/240 VAC Version, onlyCAUTION: Do not open or remove SRPM cover (tool required) with input

Commentaires sur ces manuels

Pas de commentaire

Setra Systems SRPM Instructions d'exploitation

Naviguer en ligne ou télécharger Instructions d'exploitation pour Mesure, test et contrôle Setra Systems SRPM. Setra Systems SRPM Operating instructions Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels