Setra Systems 12000C Spécifications Page 91
- Page / 133
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Technical Setup • Super II 91
SETUPS
TECH
SETUP
MORE
MORE
abc reset
tare
menu remote
DIG INP
Soft Key:
DIG INP
Setting the Digital Inputs
Digital Inputs allows an external system to signal the contoller to perform an action. There are two digital
input ports: Input 1 is located on pin 3 of the IN port and Input 2 is located on pin 5 of the IN port. The
input port is triggered when the voltage on the ports goes from Ø volts (off) to 5 volts (on). When an input
is triggered, the controller performs a preselected action. The list of actions that can be selected include
zeroing, taring, printing, accumulating the weight or count, controlling the alarms, and controlling the
prompting macros.
To setup the DIGITAL INPUTS either follow the menu tree or press the softkeys in the order below:
The following menu is displayed and the soft keys change to:
The screen shows the current function that the INPUT 1 and INPUT 2 digital ports are programmed to
perform. Select the INPUT 1 or the INPUT 2 soft keys to program the input port function.
Pressing the INPUT 1 or INPUT 2 soft key will make the following menu and soft keys appear:
Using the numeric keypad, make your selection for the function of either INPUT 1 or INPUT 2.
NONE GO BACK
Select function of Digital INPUT 1:
1. Zero 5. Start Alarms
2. Tare 6. Stop/Reset Alarms
3. Print 7. Next Macro Step
4. Accumulate 8. Restart/Exit Macro
INPUT 1 INPUT 2 GO BACK
Select Digital INPUT to be programmed:
INPUT 1: None
INPUT 2: None
- Super II 1
- Table of Contents 2
- Introduction 4
- • Super II 6 6
- • Super II 8 8
- Supervisor Setup 9
- • Super II 10 10
- PRINT SETUP 11
- Programming a PRINT Format 12
- * Setra 300/COSTAR 13
- • Super II 14 14
- Selecting Fields to Print 15
- ID Fields 16
- Interval Print Programming 17
- • Super II 18 18
- SAMPLE SETUP 19
- ACCURACY 20
- SETUP 20
- ACCURCY SETUP 21
- BI* OUT IN GO BACK 22
- PORTS SETUP 23
- 12 HR 24 HR 24
- TIME DATE 25
- • Super II 26 26
- UNITS 27
- UNITS ENABLED 28
- FACTOR DIVISOR 29
- NAME RESOLUT ON/OFF GO 29
- DATABASE 30
- DATBASE SETUP 31
- 5 6 GO BACK 32
- 5. FULL DATABASE 32
- 6. DATABASE OFF 32
- • Super II 33 33
- • Super II 34 34
- TRANSAC SETUP 35
- • Super II 36 36
- • Super II 37 37
- ID0: PART ID ID4: DESC ID8: 38
- ID1: OPRTR ID5: VENDOR ID9: 38
- ID2: ORDER # ID6: REV # 38
- ID3: LOT # ID7: 38
- ID NAME SETUP 39
- ENTER 40
- • Super II 41 41
- MACRO SETUP 42
- Programming a Macro 43
- • Super II 44 44
- • Super II 45 45
- • Super II 46 46
- SECURITY 47
- SETUP SECURTY 48
- • Super II 49 49
- BEEPER CONTROL 50
- Bases Setup 51
- • Super II 52 52
- Select calibration option: 54
- 1. BASE 1 5. BASE 5 56
- 2. BASE 2 6. BASE 6 56
- 3. BASE 3 7. BASE 7 56
- 4. BASE 4 8. BASE 8 56
- Soft Key: 57
- • Super II 58 58
- Bases Menu: Soft Key NAME 64
- Changing the Name of a Base 65
- Bases Menu: Soft Key ADDRESS 66
- • Super II 68 68
- Bases Menu: Soft Key BASERST 69
- Resetting the Base 70
- Technical Setup 71
- GREETING 72
- Setting the Power-Up Greeting 73
- BAT LIM DELAY ON INPT GO BACK 74
- Backlighting of the Display 75
- TRANSFER 77
- SETUP TRANSFR 78
- ALL COUNT 82
- AUTO SWITCH 85
- Setting Up the Alarm Outputs 87
- LOW TARGET HIGH LATCH 88
- ALARM 2 LO LO HI HI 88
- INPUT 1 INPUT 2 GO BACK 90
- Setting the Digital Inputs 91
- ON OFF GO BACK 94
- Improving Display Stability 95
- APW QTY 96
- APW PIECES: 1000 98
- Appendix A 99
- Sending Commands to the Scale 100
- 101 101
- 103 103
- Interval Print Mode 103
- The Jump Function 103
- Status After Power is Applied 104
- The Quantity Function 104
- The Verify Function 104
- 105 105
- The RS232 Interface Hardware 105
- Appendix B 106
- ScriptCoder 106
- Custom Label Printing 106
- Entering a Script Using a PC 108
- ASCII Control Characters 113
- Appendix C 114
- Battery Option 114
- Figure 2 115
- Appendix D 116
- Figure 3. Cable Preparation 118
- Calibration 119
- Press END 121
- Appendix E 122
- SPECIFICATIONS 122
- 123 123
- • Super II 124 124
- Appendix F 125
- Glossary of Terms 125
- • Super II 126 126
- Setra Systems, Inc 127
- Appendix H 128
- WARNINGS 128
- FCC Warning 129
- EC Declaration of Conformity 130
- Index • Super II 132
Produits connexes et manuels pour Balance de cuisine Setra Systems 12000C
(18 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.913 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels